/wp-content/uploads/2025/08/Flux_Schnell_a_lush_3d_render_of_Futuristic_space_age_vector_l_3-300x300.jpg Can You Reach Your Pump? Test Your Signal Before Fire Season - Wildfire Watchdog

If your plan is to start a pump from somewhere else, the pump is only half of it. The other half is the signal. Good equipment is useless if nobody checked whether it can be reached when it counts.

November is a good time to test this, while nothing is burning and you have time to fix what you find.

Know what you're relying on

A remote-start setup needs a path between your phone and the pump. That path usually runs through one of two things:

  • WiFi at the pump. Your router, a long-range access point, or a hotspot. It needs power and a working internet connection.
  • Cell service for text messages. SMS often goes through where data and video calls don't, because a text needs far less signal.

Rural properties are tricky. Your house might have great WiFi and the pump shed 300 feet away gets nothing. Or the reverse: no WiFi at the shop, but one bar of cell by the tank.

Walk the property and test it

This takes about an hour with your phone.

  1. Stand at the pump location and check your phone's signal. Send a text to yourself and see how long it takes.
  2. Run a speed test on WiFi at the pump, if you have it. You don't need fast. You need steady.
  3. Check the signal again at a different time of day. Rural networks can slow down in the evening.
  4. Turn your phone's WiFi off and try the same thing over cell only. That's closer to what you'll have when you're away from home.

If the signal is weak, a wired access point, an outdoor antenna, or a cell booster aimed at your carrier's tower can make a big difference. Pick the carrier that works at your place, not the one you've always had.

Plan for power and internet going out

Fires and power don't mix well. Utilities sometimes shut power off ahead of wind events, and fire can take out lines and cell towers. Ask yourself:

  • If your power goes out, does your router and modem go with it?
  • Is there a battery backup on the router? A small UPS can keep a router going for hours.
  • Does your pump's controller have its own power, or does it depend on the house?
  • If the internet is down, do you have a second way in, like text messages?

Having two paths is the point. If one fails, you have another.

Set up alerts, then test them

Starting a pump is one thing. Knowing it's still running is another. A pump can quit because it ran out of gas, lost prime, or the tank ran dry. If you're two hours away, you want to hear about it.

That's how I built the Dry Lightning 3000. It's a Honda iGX390 pump, up to 150 GPM and up to 140 PSI, and you start and stop it from your phone over WiFi or SMS from anywhere. It sends you an alert if the pump stops running, like when it runs out of gas, or if the water tank runs low. Whatever pump you run, I'd want those same two alerts: pump stopped, and tank low.

And test the alerts. Don't assume. Make sure they actually reach your phone, including when your phone is on Do Not Disturb at night. Many phones let you let certain contacts or apps through.

Do a full dry run

Once you've checked signal, power, and alerts, do the whole thing the way you'd do it for real:

  1. Drive down the road until you're a few miles away, or go to a neighbor's.
  2. Start the pump from your phone.
  3. Confirm it's running and the water is moving, and check your sprinklers or hose lines.
  4. Stop it from your phone.

If something didn't work, you just learned it at a good time. Write down what fixed it and keep that note with your evacuation papers.

One thing to do this week

Pick one evening and take a drive a couple miles from your place. From there, try to start and stop your pump, and see if you get an alert when it stops. If you can't, find out why now, and fix the weakest link first, whether that's the signal at the pump, the power to your router, or the alert settings on your phone.